looking to rewire my tail lights for my 1968 f100 ranger, any ideas on a good source? i could build my own but want to check out pricing
thanks dave
gowen mi
tail light wiring harness #13A409
Moderators: FORDification, Thunderfoot
-
- New Member
- Posts: 11
- Joined: Mon Feb 01, 2016 12:47 pm
- sargentrs
- 100% FORDified!
- Posts: 9866
- Joined: Fri Jun 22, 2007 9:30 am
- Location: Georgia, Jasper
Re: tail light wiring harness #13A409
You'll come out far cheaper making your own. Everything I've ever seen will run you $150-$200.
Randy
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
- Ranchero50
- Moderator
- Posts: 5799
- Joined: Wed Nov 08, 2006 7:02 pm
- Location: Maryland, Hagerstown
- Contact:
Re: tail light wiring harness #13A409
Ditto, depends on what you are doing, driving or concourse resto. Try to avoid any crimp connectors. I like to solder and heat shrink everything, grease it before shrinking if it's going to be driven during the winter.
'70 F-350 CS Cummins 6BT 10klb truck 64k mile Bahama Blue
Contact me for CNC Dome Lamp Bezels and Ash Tray pulls.
Contact me for CNC Dome Lamp Bezels and Ash Tray pulls.
-
- New Member
- Posts: 11
- Joined: Mon Feb 01, 2016 12:47 pm
Re: tail light wiring harness #13A409
yep, you guys talked me into making my own, what gauge wire is necessary?
dave
dave
- Ranchero50
- Moderator
- Posts: 5799
- Joined: Wed Nov 08, 2006 7:02 pm
- Location: Maryland, Hagerstown
- Contact:
Re: tail light wiring harness #13A409
Factory was probably 16ga. I tend to run 14 ga since it stands up the vibration and overcurrent better. I'll buy a couple bags of blue crimp fittings, peal the blue crimp collar off and solder them to the wiring trying to leave the butt end solder free so the wire is less prone to break that way. Slip some heat shrink over and heat set it.
'70 F-350 CS Cummins 6BT 10klb truck 64k mile Bahama Blue
Contact me for CNC Dome Lamp Bezels and Ash Tray pulls.
Contact me for CNC Dome Lamp Bezels and Ash Tray pulls.
- sargentrs
- 100% FORDified!
- Posts: 9866
- Joined: Fri Jun 22, 2007 9:30 am
- Location: Georgia, Jasper
Re: tail light wiring harness #13A409
only I got tired of peeling off the insulation and bought these. https://www.delcity.net/store/Non-Insul ... 4tEALw_wcB Careful, it's an addiction. Liked it so much I bought this https://www.amazon.com/Terrans-Non-Insu ... 9341&psc=1
Also made this nifty little jig to hold the wires while I solder them. Easily clamped to any table or bench. Wait for the opportune time when wifey is out of the house for awhile and have fun like I did wiring my Fairlane with an ATO fuse panel on the living room coffee table
Also made this nifty little jig to hold the wires while I solder them. Easily clamped to any table or bench. Wait for the opportune time when wifey is out of the house for awhile and have fun like I did wiring my Fairlane with an ATO fuse panel on the living room coffee table
You do not have the required permissions to view the files attached to this post.
Randy
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
-
- New Member
- Posts: 11
- Joined: Mon Feb 01, 2016 12:47 pm
Re: tail light wiring harness #13A409
awesome info, the tail light assembly comes with the snap plug connectors, how did you connect your home made wiring harness to the tail light assembly?
thanks again
dave
thanks again
dave
- sargentrs
- 100% FORDified!
- Posts: 9866
- Joined: Fri Jun 22, 2007 9:30 am
- Location: Georgia, Jasper
Re: tail light wiring harness #13A409
Several of the regular vendors have light sockets and pigtails https://www.macsautoparts.com/ford_truc ... ckets.html and you can sometimes find them at your local parts stores, in the HELP section, or they can order them. If the pigtail didn't have a matching plug, I improvise with bullet connectors.
Randy
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.